Spars & Rigging

Anodized aluminium sheaves with acetal center bush. Some old stock may be supplied with a tufnol bush. Aluminium sheaves provide great wear resista...

Chain / Shroud Plates - Polished gunmetal bronze. To ensure correct positioning of the plates to the vessel, they are supplied undrilled, thus allo...

Half Cowl Vent - Left or Right Hand - Cast from gunmetal bronze, these vents are designed to fit to the sides of engine compartments. They are usua...

Adapter plate for split backstay adjuster. Fits onto Harken 38mm wire blocks #304. Weight (g) 28 g Weight (oz) 1 oz

High-load sheaves are offered as replacement parts or for use in special applications. Their bearing system combines sideload-carrying balls with a...

Track is extruded from high-grade 6061-T6 aluminum and hardcoat-anodized for a hard, long-lasting surface. Has 4 inch imperial hole spacings rather...

Race once with the windward sheeting traveller car and you’ll never race without one again. Pull the car above the centerline without releasing the...

Race once with the windward sheeting traveller car and you’ll never race without one again. Pull the car above the centerline without releasing the...

Stand-up toggles hold blocks upright on travellers. Fits harken Big Boat 32mm traveller cars. Mainsheet block pin Ø (mm) 8 mm Mainsheet block pin Ø...

Self-contained sheaves are designed for sailors to use in custom applications. 2760 sheaves are Delrin® acetal resin with Delrin® ball bearings. Th...

Endstops are designed to absorb shock loads and should be installed when end controls are not used. Length (mm) 55 mm Length (in) 2 3/16 in Width (...

Hardcoat-anodized aluminum endstops absorb shock loads and prevent damage to the car. Use with 1706 low-beam ball bearing pinstop track. Length (mm...

Hardcoat-anodized aluminum endstops absorb shock loads and prevent damage to the car. High-load stainless steel diamond-shaped padeye for block att...

When end controls are not used, add endstops to absorb shock loads. Fits Harken 22 mm High Beam Ball Bearing tracks. Fasteners (mm) 5 mm Fasteners ...

Lazy Jacks contain mainsails while reefing and dousing allowing the mainsail to be raised and lowered from the cockpit without going on deck. They ...

Lazy Jacks contain mainsails while reefing and dousing allowing the mainsail to be raised and lowered from the cockpit without going on deck. They ...

Track is extruded from high-grade 6061-T6 aluminum and hardcoat-anodized for a hard, long-lasting surface. Length (m) 3.6 m Width (mm) 42 mm Width ...

Harken Stand-up toggles hold blocks upright on travellers. Fits Harken Midrange 27mm cars. Mainsheet block pin Ø (mm) 6, 8 mm Mainsheet block pin Ø...

Hardcoat-anodized aluminum pinstop end controls limit car movement on the track. Bumpers absorb shock loads and prevent damage to the car. Fits Har...

Big Boat sheaves are available for special applications as well as for replacement sheaves in Big Boat blocks. Made of hardcoat-anodized, PTFE-impr...

Use 1849 risers for mid-boom travellers that must clear companionway hatches. Risers fit most cabintops and articulate for use with either straight...

Big Boat sheaves are available for special applications as well as for replacement sheaves in Big Boat blocks. Made of hardcoat-anodized, PTFE-impr...

These adapters upgrade many ball bearing CB traveller cars to race-ready windward sheeting cars. Adapters also fit several older non-CB cars. They ...

Safety helmet for work at height, yacht rigging, industrial activities and building construction. Lightweight helmet, comfortable and well ventil...

 Get the most out of your sailboat with the Loos PT series of gauges. These gauges are designed for setting the proper tension in the standing rigg...

Marlow hot knife for cutting and heat-sealing ropes in one stroke. Use in conjunction with Marlow Tape for a perfect clean, neat cut that also prev...

Mast or bowsprit bands cast in gunmetal bronze with 4 eyes. Made by Davey and Co London. Available in several sizes to suit different mast diameters.

Nylon shackle for holding sail slugs onto mainsail. Screw attachment. DIMENSIONS External Length: 31mm External Width: 13mm Internal Length: 17mm I...

Closed body rigging screws. Chrome plated bronze body with 316 stainless steel ends. Available in several thread sizes with different end options....

Riley Combination flat head screwdriver and shackle spanner Nylon and Stainless Steel construction Fits most small shackles. Length: 142mm.

Riley bronze sheave suitable for rope or wire. Bronze provides low friction turning and great wear resistance. DIMENSIONS: Outside Diameter: 38mm ...

Riley chrome plated bronze sheave suitable for rope or wire. Bronze provides low friction turning and great wear resistance. DIMENSIONS: Outside D...

Ronstan’s range of Acetal sheaves is moulded from a specially modified ultra-violet resistant grade of material to provide a long service life in t...

Ronstan Threaded swage terminals (2.5-26mm wire) have rolled right hand UNF threads for greater strength. Applications •For wire end termination...

Rubbaweld Mast Boot Tape is a Self amalgamating tape that welds to itself by chemical action to form a waterproof covering. This tape is a non-adhe...

Seasure Rip-Stop spinnaker repair tape. Lightweight and very strong, this self adhesive spinnaker repair tape makes a rapid long-lasting repair to ...

PNP Sheave Glass reinforced for greater strength and abrasion resistance. •Glass reinforced Nylon suitable for high load applications. Comes in a ...

New Rig Tension gauges for repeatable rig settings, aids race set up and preparation.NOW AVAILABLE IN 5-8MM SIZE Rig-Sense is a new rig tension dev...

Heavy duty soft tool bucket for carrying large items aloft. Ideal for riggers and anyone working up masts or at height or as a general purpose tool...

Spinlock Winch Feeders fit aft of clutches or jammers to divert lines to an alternative winch. Useful for leading a line from a clutch on one side ...

Spinnaker Pole End in Polished gunmetal bronze - A stylish end socket to fit a wooden spar. Sprung piston end. SPINNAKER POLE END SIZING SMALL - 10...

Stem head Fitting cast in polished gunmetal bronze. This strong stem head fitting takes the load down the front of the stem and is suitable for cra...

Toledo Wire crimping hand tools for copper or aluminium talurit crimps. Ideal for swaging loops on to the end of wire ropes. •Designed to compress ...

Homer Turnbuckles with eye and hook. Made from 316 Stainless Steel. Available in 2 sizes. Thread size - Closed length6MM - 160MM8MM - 200MM This it...

The perfect wind indicator for smaller dinghies/multihulls or other fast sailing crafts. Suitable for boats less than 20 feet. Flexible mounting fi...

Mast Bracket with Windicator Opti S. Specially designed for the Optimist with 300mm long support to clear Gaff.

Wire rope grips galvanized. The easy way to create loops in the end of wire ropes. Simply loop the wire through and tighten the bolts. Available in...

Wykeham Martin Furling GearIn continuous production for over 100 years, this traditionalfurling gear has been successfully fitted to thousands of b...