Products

Harken recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. The 7404 kit’s lightweight, UV-stabilized Carbo ...

The halyard deflector prevents the jib halyard and other halyards (such as a spinnaker or additional jib halyards) from wrapping around the foil. ...

When end controls are not used, add endstops to absorb shock loads. Fits Harken 22mm Small Boat Tracks. Fasteners (mm) 5 mm Fasteners (in) #10 FH i...

When end controls are not used, add endstops to absorb shock loads. Fits Harken 22mm High Beam Tracks. Fasteners (mm) 5 mm Fasteners (in) #10 FH in...

Lazy Jacks contain mainsails while reefing and dousing allowing the mainsail to be raised and lowered from the cockpit without going on deck. They ...

Lazy Jacks contain mainsails while reefing and dousing allowing the mainsail to be raised and lowered from the cockpit without going on deck. They ...

Track is extruded from high-grade 6061-T6 aluminum and hardcoat-anodized for a hard, long-lasting surface. Length (m) 3.6 m Width (mm) 42 mm Width ...

Harken Stand-up toggles hold blocks upright on travellers. Fits Harken Midrange 27mm cars. Mainsheet block pin Ø (mm) 6, 8 mm Mainsheet block pin Ø...

Harken® recommends equipping every furling system with Carbo lead blocks for safe furling from the cockpit. The 7403 outboard assembly allows furli...

Hardcoat-anodized aluminum pinstop end controls limit car movement on the track. Bumpers absorb shock loads and prevent damage to the car. Fits Har...

Prefeeders facilitate fast sail changes. The 7006 prefeeder features hardcoat-anodized rollers with low-friction bushings. Fits any Harken Carbo Ra...

Harken R27 high beam end stops. Endstops are designed to absorb shock loads and should be installed when end controls are not used. Use with R27HB ...

Harken Midrange 27mm ball bearing track for retrofit installations requiring a 4 inch (102mm) hole spacing. Track is extruded from high-grade 6061-...

Splice links join track and keep it aligned during installation. Use to join Harken R27 midrange low beam track.

Use 1849 risers for mid-boom travellers that must clear companionway hatches. Risers fit most cabintops and articulate for use with either straight...

When end control assemblies are used, trim caps finish track ends.Fits Harken 27mm midrange High Beam tracks. Sold in pairs. Footnote Trim caps not...

When end control assemblies are used, trim caps finish track ends. Fits Harken 27mm midrange tracks. Sold in pairs. Use with track 1602, 1616, 1617...

Big Boat sheaves are available for special applications as well as for replacement sheaves in Big Boat blocks. Made of hardcoat-anodized, PTFE-impr...

These adapters upgrade many ball bearing CB traveller cars to race-ready windward sheeting cars. Adapters also fit several older non-CB cars. They ...

Highfields Pattern Running Backstay Lever - Gunmetal channel section, polished outside and pivoted with two side bolts leaving the channel clear fo...

Homer Folding Step 316 Stainless Steel. Can be used as a folding mast step as well as many other uses on boats, campervans and RVs. Base Size: 110 ...

Homer Sail Track Stop Internal portion of stop dimensions: • Length: 22mm •ø 13mm •Weight 41gr

Homer shackle spanner 316 stainless steel. Suits most shackle sizes. Length: 112mm Weight: 22g

Spreader Boots (PVC Anti Chafe Covers) White Plastic Spreader Protector. These protective covers protect the sails from damage and chaffing from co...

Homer Eye to Eye Open body Turnbuckle.Aisi 316 stainless steel.Available in 3 sizes.Not Load Rated SPECIFICATIONS5mm Turnbuckle:- Thread Diameter: ...

Homer Jaw to Jaw Open body Turnbuckle. Available in three sizes. AISI 316 Stainless Steel Not Load Rated Specifications:5mm Turnbuckle:- Thread Dia...

KONG Pressure die-cast Jib Hanks. These are made of steel bronze (softer material than the stainless steel of the stay), therefore they do not dama...

Plate for multiple connections, allows simultaneous connection up to 6 users. It is an anchor device with multiple attachment points that can be co...

Safety helmet for work at height, yacht rigging, industrial activities and building construction. Lightweight helmet, comfortable and well ventil...

2m Retractable fall arrester with automatic recall for both horizontal and vertical use and with fall factor 2.Can also be used on mobile elevating...

Tris Anchor Plate Rigging plater with 3 holes, 20mm diameter, designed to organize a tidy workplace and to create an easy system of multiple anchor...

 Get the most out of your sailboat with the Loos PT series of gauges. These gauges are designed for setting the proper tension in the standing rigg...

Steel Marlin Spike with lanyard attachment. Made by Davey and Co London. We carry limited stock in NZ so please contact sales to check stock before...

For high-load, diameter or safety critical applications, D12 MAX is the only choice, either covered or uncovered. Stiffer than standard D12, D12 MA...

Splicing needles used for MARLOWBRAID (quick splice), D2 (covered Dyneema splice) and can be used on D12 (12 strand Dyneema splice). DIMENSIONS: Sm...

Mast or bowsprit bands cast in gunmetal bronze with 4 eyes. Made by Davey and Co London. Available in several sizes to suit different mast diameters.